Broadcast DPS ES-2200 Manual del operador descargar pdf (Pagina 13)

9. Install the 3 wire RS-232 cable for unit 2 (figure 2-1) to the 3 pin header labeled INPUT at the top of the second

card near the BNC connectors.

10. If there is a card intended for the unit 2 position, press the power supply's edge connector for unit 2 onto the second

card as far as it will go.

11. Mount the second card in the unit 2 position using the five screws provided and install the supplied hardware for

the rear panel support bracket and install the top cover.

Note: DIP Switch 1 on both the ES-2200S chassis and the cards installed therein controls baud rate.

UP 9600 B/s

DOWN 31.25 kB/s

There is no advantage to either setting, but the baud rate must be set to the same rate for both the installed cards and the

ES-2200S chassis.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 69 70

Operator’s Manual 1
Table of Contents 2
Table of figures 4
Introduction 5
Compatible DPS Products 6
Chapter 1: 7
Installation 7
ES-2200 Front Panel 8
ES-2200 System Configuration 9
ES-2200T Card Installation 11
ES-2200S Card Installation 12
Chapter 2: 14
ES-2200T Operation 14
Figure 2-2: ES-2200T Controls 15
TBC Card Controls 16
Proc Amp 16
Memory Functions 17
Freeze Controls 18
C – F (GENLOCK TIMING) 19
TBC Configuration 20
TBC Configuration Functions 21
TBC IV Option Card Controls 21
V-Scope Controls 22
23
Shaft Encoder 24
Chapter 3: 25
ES-2200S Operation 25
Unit Select 26
MicroSYNC Controls 27
Proc Amp Controls 27
Function 28
WHITE CLIP (VS-2410 Only) 29
BLACK CLIP (VS-2410 Only) 29
MicroSYNC CONFIGURE Select 30
Chapter 4: 34
Video Connections 34
Personal TBC IV Connectors 36
NTSC VIDEO OUTPUT 37
GENLOCK OK LED 37
GENLOCK VIDEO INPUT 37
Figure 4-4: TBC IV Card 37
SERIAL DATA INPUT (RJ-14) 38
NTSC VIDEO INPUT 38
REFERENCE VIDEO INPUT 39
GENLOCK TIMING ADJUSTMENT 39
MULTI I/O (DB-9) 40
GENLOCK LOOP THROUGH 40
NTSC BNC VIDEO OUTPUT 41
NTSC BUS VIDEO OUTPUT 41
Personal V-Scope Connectors 42
BUFFERED VIDEO OUTPUT 43
SUPERIMPOSE OUTPUT 43
FULL TIME OUTPUT 43
Connectors 44
BNC OUTPUT 45
BNC CONTROL 45
Personal VDA Connectors 46
TERMINATION SWITCH 47
Figure 4-14: VDA Card 47
Chapter 5: 48
Remote Control 48
Card Addressing 50
RC-2000 Remote Control 51
RC-2001 Remote Control 52
System Addressing 52
Computer Control 54
Appendices 56
Appendix A: Specifications 57
Serial Data Input 57
Power Requirements 57
Physical Characteristics 57
Appendix B: Serial Protocol 58
Electrical Interface 58
Protocol 58
System Exclusive Byte 58
TBC/MicroSYNC/V-Scope ID Byte 59
Unit Address Byte 59
MicroSYNC Configuration Bytes 62
TBC IV Configuration Bytes 63
INTERNET 65
CANADA/INTERNATIONAL 65
ASIA AND THE PACIFIC RIM 66
Appendix E: Warranty 68
Warranty Statement 68
Warranty Limitations 68
Warranty Service 69
Appendix F: Compliance 70
FCC Compliance Statement 70

Comentarios a estos manuales

Sin comentarios

Broadcast DPS ES-2200 Manual del operador Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos Broadcast DPS ES-2200